轮箱/齿轮箱样本
齿轮箱样本 (pdf) 齿轮箱样本 (html)

ITG公司的产品仅出售给主机设备制造厂
轴和齿轮布置简图
主页 齿轮箱主页

索取齿轮箱样本 与我们联系

机器简图1和2 Shaft and Gear Arrangment SchematicsSuper 200 Wing GearboxGearbox Request Form

旋向和90度角

Each ITG assembly is assigned a individual number. In addition to this number is a description of the assembly. If no assembly number is shown in the catalog sheet for the Series and arrangement you require for your application, then the assembly can be specified by the description, base on the following example.

Example; 30 Series assembly #01-004 the description is,
ITG-30S-1:1.47SU-1 3/8”-6

#1
#2
#3
#4
#5
#6
#7
#8
#9
30
S
1:1.47
SU
1 3/8"
6
1 3/8"-20
?“O45”
?

 

  • NOTE:
    注：CCW=逆时针 CW=顺时针。上述示例描述了由轴端看去轴的旋转方向。在
    轴上面画出的箭头表示出轴的旋转方向。
  • CCW = 逆时针
  • CW = 顺时针。

 

#1 Series Number
#2

Shaft & gear arrangement.

  • "S" = Standard in Rotary Cutter gear boxes and is the
    same as “F” & “G” in Schematic table for Right Angle Boxes.
  • "R" = Reversed in Rotary Cutter gear boxes and is the
    same as “B” & “C” in Schematic table for Right Angle Boxes.
  • ?"T" = Through shaft in Rotary Cutter applications,and is the
    same as “D” & “E” in Schematic table for Right Angle Boxes.







#3
  • "1:1.47" = Speed Increasing gear ratio.
  • "1.47:1" = Speed Reducing gear ratio
#4
  • "SU" = Speed Increasing. This is secondary specification to #3 above.?
  • "RD" = Speed Reducing. This is secondary specification to #3 above.
#5
  • "1 3/8" = Input Shaft diameter in inches. Also see #7, #8, & #9 below
    for other shafts sizes on multiple shaft boxes.
  • "O35" = Input Shaft diameter in milliliters.?
#6
  • "6" = Indicates Spline shaft that has 6 teeth.
  • "20" = Indicates Spline shaft with 20 teeth.
  • "SB" = Shear Bolt. The driving force is transmitted to the Input Shaft through a bolt.?
#7
  • ? "1 3/4"-20" Used to specify Output Shaft #2 size. Example: See #5 & #6 above.?

#8
  • “O45” Used to specify Output Shaft #3 size in millimeters. Example: See #5 & #6 above.
#9
  • Used to specify Output Shaft # 4 size on arrangements “H” & “I”. Example: See #5 & #6 above

     

    • The 齿轮箱 are offered in 3 basic configurations, that would be like the letters “L”, “T”, and “X”
    • Each configuration can be arranged in different speed increasing or speed reducing and shaft rotations as shown in the following schematics.
    • Some types of assemblies are limited to the “L” and “T” configurations only.
    • Any shaft can be used as the Input Shaft. For illustration the shaft noted as
      #1 is considered the Input Shaft.

       

打印本页

索取申请表
农机器具/割草机总成及零部件 齿轮箱  动力输出轴 养路设备
农具样本(pdf) 农具样本(html) 齿轮箱样本(pdf) 齿轮箱样本(html)
新闻 公司介绍 国际工业制造网络 我们对质量的承诺
网站图 网站图 与我们联系
受版权法保护
受版权法保护
©1984-2005 a Jenkins Enterprises, 有限公司